The Introduction to the Use of Bending Machine

  First, turn on the power, turn on the key on the control panel, and press the pump to start, so you can hear the sound of the pump. ( the machine does not move at this point)

  When we adjust the stroke, the plate press brake must be used to adjust the stroke, and we must test the car before bending. When the upper die of the bending machine goes down to the bottom, there must be a thick gap between the bottom , otherwise it will cause damage to the mould and the machine. The adjustment of stroke also has electric quick adjustment and manual fine adjustment.

  The choice of bend slot, generally we choose the plate thickness of 8 times width slot. If the sheet that bends 4 mm, we need to choose the slot of 32 or so.

  The adjustment of the backstop is generally electric quick adjustment and manual adjustment, the method is the same as the shearing machine.

  Step on the foot switch to start bending, bending machine and shearing machine are different, they can release at any time, when the bending machine is released, it will stop and continue to fall if it continues.

  There are many kinds of bending machines of sheet metal processing, which can be divided into mechanical (servo motor) and hydraulic type. The control system can be divided into simple manual bending machine, ordinary domestic digital positioning bending machine, process control digital full-function bending machine. According to the action part they can be divided into 4, 8, 12, and other bending machines.

  1. Before using the bending machine, check whether the power supply is connected, whether the air pressure is enough, whether the hydraulic pressure is sufficient, whether the machine is clean, whether the slide section has the obstacles, and the following procedure can be carried out after confirmation.

  2. Turn on the machine power switch, the starting oil pump is the origin of the L axis, D axis, CC axis and Z axis, and complete the starting process.

  3.After the mold is selected, the stop switch of the machine is placed in the cut position. After the install of the base and the bottom die and the top die, the switch of the machine is placed in an inch or single position. Step foot up switch to shake up the swing handle or knob to combine the upper and lower modes and pressurize the zero point of the good D axis, and lock the die to complete the molding process.

  4.Make a map, and then begin to program the folding machine after understanding the bending sequence and bending size. There are two input methods for programming, one for Angle input and the other for depth input. We often use depth input method. First, the computer is entered into the state of mind, and the number of bending dimensions L, D, Z, speed, time and number are entered. Then check the confirmation procedure, make the computer go into operation, and then use the waste test to modify the program, so that the Angle and size can be adjusted to the optimal state. Then the product will be tested and the samples will be manufactured in batches after inspection.

  5.In the bending process, if you want to improve the bending speed, you can move or connect the stop switch, but you can only use single motion for the sake of safety. When the workpiece is bent longer, the middle angle is large, and the CC axis can be adjusted to change the middle angle to achieve the same angle with the left and the right sides. In the bending process, we should also pay attention to the bending principle of the center, which is an important precondition for ensuring the accuracy of bending and bending, and it is not allowed to bend at the end of the bending machine. This Angle is not only bad, but also damages the machine.

  6.It is not allowed to turn off the power supply during the short break, so that the oil pump can be turned off, and so as to save the electricity bill, so as to eliminate the work of the original starting point, and save time and improve the standing rate.

  7.When you finish the product or after work, you need to stop, first we put the die down to the lowest level, then turn off the oil pump and turn off the power. If this batch of products are finished, you must also remove the mold and return it to the rack and return to the operation panel.

  8.It is strictly forbidden to operate the bending machine to avoid unnecessary damage to the personal and equipment mould. We should pay attention to the cleaning and maintenance of the machine, and develop good habits of protecting equipment and mold.