- \n
- Configuration parameters<\/strong> (Menu option 2) – machine setup and behavior settings<\/li>\n\n\n\n
- Axis parameters<\/strong> (Menu option 1) – calibration and movement characteristics<\/li>\n\n\n\n
- Work programmes<\/strong> – both graphic and numeric bending sequences<\/li>\n\n\n\n
- Equipment<\/strong> – punch and die tooling definitions<\/li>\n<\/ul>\n\n\n\n
Each of these data types resides in specific memory locations and requires different handling procedures for backup and recovery.<\/p>\n\n\n\n
Memory Devices in ESA S875<\/h2>\n\n\n\n
ESA S875 Windows memory management utilizes four primary memory devices, each serving a specific purpose in the system architecture:<\/p>\n\n\n\n
Flash Memory<\/h3>\n\n\n\n
The Flash memory is the resident device located on the MULTIFUNCTION board. It contains the management software that controls machine movements along with its operating system. This is the foundational memory that makes the control system function.<\/p>\n\n\n\n
Internal Memory (Buffered RAM)<\/h3>\n\n\n\n
This is the working memory of the numeric control, also located on the MULTIFUNCTION board. All machine data are downloaded here before being used during operation. Thanks to an internal battery, these data remain stored even when the control is turned off, preventing loss of active configurations and programs during power-down.<\/p>\n\n\n\n
SSD (Flash Hard Disk)<\/h3>\n\n\n\n
The SSD is a critical component within ESA S875 Windows memory management. It contains:<\/p>\n\n\n\n
- \n
- A copy of the operating system<\/li>\n\n\n\n
- The S 675 Touch and S 875W application programme<\/li>\n\n\n\n
- A backup copy of the application programme<\/li>\n\n\n\n
- Series data saved by the application (machine data, programmes, and equipment)<\/li>\n<\/ul>\n\n\n\n
The SSD serves as the primary long-term storage for your machine’s data, ensuring that even if other memory systems experience issues, a recoverable copy exists.<\/p>\n\n\n\n
USB Device<\/h3>\n\n\n\n
The USB device (standard USB 1.1 or USB 2.0 pen drive) is the primary tool for data transfer and external backup within ESA S875 Windows memory management. It is used to:<\/p>\n\n\n\n
- \n
- Save configuration parameters and axis parameters<\/li>\n\n\n\n
- Create security copies of programmes, punches, and dies<\/li>\n\n\n\n
- Transfer data to and from IBM-compatible personal computers for additional backup and analysis<\/li>\n<\/ul>\n\n\n\n
Logic Location of Data<\/h2>\n\n\n\n
Understanding where data resides during different operational states is fundamental to ESA S875 Windows memory management. When the machine is turned on and in use, all data reside in the internal memory (buffered RAM) for quick access. However, the permanent storage locations vary by data type:<\/p>\n\n\n\n
Type of Value<\/th> Memory Device<\/th><\/tr><\/thead> Configuration parameters<\/td> Internal memory + SSD<\/td><\/tr> Axis parameters<\/td> Internal memory + SSD<\/td><\/tr> Work programmes<\/td> SSD<\/td><\/tr> Punches<\/td> SSD<\/td><\/tr> Dies<\/td> SSD<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n All machine data (Configuration and Axes) are stored as files, enabling recovery in case of incorrect entry or memory loss. This file-based approach within ESA S875 Windows memory management makes data transfer and backup straightforward.<\/p>\n\n\n\n
Exchanging Data Between Memory Devices<\/h2>\n\n\n\n
Data exchange is a core function of ESA S875 Windows memory management. This refers to transferring data between internal memory devices and the USB device. Two primary operations exist:<\/p>\n\n\n\n
- \n
- SAVING<\/strong>: Transferring data from internal memory to USB device<\/li>\n\n\n\n
- UPLOADING<\/strong>: Transferring data from USB device to internal memory<\/li>\n<\/ul>\n\n\n\n
An important feature of ESA S875 Windows memory management is that during uploading or saving of configuration or axis parameter data, files are first saved to SSD and then transferred to the recipient device. This means that if either the USB device or internal memory malfunctions, a backup copy from the last operation always exists on the SSD.<\/p>\n\n\n\n
![\"ESA](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-12.png\")
<\/figure>\n\n\n\n![\"ESA](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-13.png\")
<\/figure>\n\n\n\nIt is also possible to simultaneously save or upload machine parameters and configuration parameters in automatic mode, streamlining the backup process.<\/p>\n\n\n\n
Managing Configuration Parameters<\/h2>\n\n\n\n
Configuration parameters define how your HARSLE press brake behaves during operation. Proper ESA S875 Windows memory management includes regular backup of these settings. The configuration parameters consist of the following data:<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-14.png\")
<\/figure>\n\n\n\nSingle Saving<\/h3>\n\n\n\n
To save one type of configuration parameter only:<\/p>\n\n\n\n
- \n
- Select the Menu Configure Machine (2)<\/em><\/strong><\/li>\n\n\n\n
- Select the type of parameters to save (keys 1 to 8) by entering the corresponding mask<\/li>\n\n\n\n
- Press the save key to save the file containing the selected data to the USB device<\/li>\n<\/ol>\n\n\n\n
Single Uploading<\/h3>\n\n\n\n
To upload a single type of configuration parameter:<\/p>\n\n\n\n
- \n
- Select Menu Configure Machine (2)<\/em><\/strong><\/li>\n\n\n\n
- Select the type of parameters to upload (keys 1 to 8) by entering the corresponding mask<\/li>\n\n\n\n
- Press [Upload from Disk<\/em>]<\/strong> to load the file from USB device<\/li>\n<\/ol>\n\n\n\n
Global Saving and Uploading<\/h3>\n\n\n\n
For comprehensive ESA S875 Windows memory management, global operations save or upload all configuration parameters at once:<\/p>\n\n\n\n
- \n
- Global Saving<\/strong>: From Configure Machine Menu (2), press [Save All<\/em>]<\/strong><\/li>\n\n\n\n
- Global Uploading<\/strong>: From Configure Machine Menu (2), press [Upload All<\/em>]<\/strong><\/li>\n<\/ul>\n\n\n\n
Managing Axis Parameters<\/h2>\n\n\n\n
Axis parameters control the movement characteristics of your press brake and are equally important within ESA S875 Windows memory management.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-15.png\")
<\/figure>\n\n\n\nSingle Saving<\/h3>\n\n\n\n
To save only the Axis Parameters:<\/p>\n\n\n\n
- \n
- Select Menu Axis Parameters (1)<\/em><\/strong><\/li>\n\n\n\n
- Press the save key to save the file containing the data to the USB device<\/li>\n<\/ol>\n\n\n\n
Single Uploading<\/h3>\n\n\n\n
To upload only the Axis Parameters:<\/p>\n\n\n\n
- \n
- Select Menu Axis Parameters (1)<\/em><\/strong><\/li>\n\n\n\n
- Press [Upload from Disk<\/em>]<\/strong> to load the file from USB device<\/li>\n<\/ol>\n\n\n\n
Saving\/Uploading All Parameters<\/h3>\n\n\n\n
For complete system backup within ESA S875 Windows memory management, you can save or upload ALL configuration and axis parameters simultaneously:<\/p>\n\n\n\n
- \n
- Navigate to Configure Machine Menu (2)<\/em><\/strong><\/li>\n\n\n\n
- Press [Save All<\/em>]<\/strong> or [Upload All<\/em>]<\/strong><\/li>\n<\/ol>\n\n\n\n
Managing Tooling Data<\/h2>\n\n\n\n
Tooling definitions for punches and dies represent significant programming investment and must be protected through proper ESA S875 Windows memory management.<\/p>\n\n\n\n
Saving\/Uploading Punches<\/h3>\n\n\n\n
The punches consist of the following data:<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-16.png\")
<\/figure>\n\n\n\nTo save a punch to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press the key to enter the punches list<\/li>\n\n\n\n
- Move the cursor to the punch you wish to save<\/li>\n\n\n\n
- Press the save key<\/li>\n<\/ol>\n\n\n\n
To upload a punch from USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press the key twice to enter the punches list<\/li>\n\n\n\n
- Press to view the list of punches on the USB device<\/li>\n\n\n\n
- Move the cursor to the punch you wish to upload<\/li>\n\n\n\n
- Press the upload key<\/li>\n<\/ol>\n\n\n\n
Saving\/Uploading Dies<\/h3>\n\n\n\n
The dies consist of the following data:<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-17.png\")
<\/figure>\n\n\n\nTo save a die to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press the key to enter the dies list<\/li>\n\n\n\n
- Move the cursor to the die you wish to save<\/li>\n\n\n\n
- Press the save key<\/li>\n<\/ol>\n\n\n\n
To upload a die from USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press the key to enter the dies list<\/li>\n\n\n\n
- Press to view the list of dies on the USB device<\/li>\n\n\n\n
- Move the cursor to the die you wish to upload<\/li>\n\n\n\n
- Press the upload key<\/li>\n<\/ol>\n\n\n\n
Saving\/Uploading All Tools<\/h3>\n\n\n\n
For efficient ESA S875 Windows memory management, you can save or upload all punches and dies simultaneously:<\/p>\n\n\n\n
To save all tools to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Enter the punches or dies list by pressing the appropriate key<\/li>\n\n\n\n
- Press the menu key and select [Save tools]<\/strong><\/li>\n\n\n\n
- All tools will be saved to the USB device<\/li>\n<\/ol>\n\n\n\n
To upload all tools from USB device:<\/strong><\/p>\n\n\n\n
- \n
- Enter the punches or dies list by pressing the appropriate key<\/li>\n\n\n\n
- Press to view the list on USB device<\/li>\n\n\n\n
- Press the menu key and select [Save tools]<\/strong><\/li>\n\n\n\n
- All tools will be uploaded from the USB device<\/li>\n<\/ol>\n\n\n\n
Managing Programmes<\/h2>\n\n\n\n
Programmes are perhaps the most frequently managed data type within\u00a0ESA S875 Windows memory management. Understanding how programmes are structured and transferred is essential.<\/p>\n\n\n\n
Programmes may consist of multiple files:<\/p>\n\n\n\n
- \n
- filename.PRG<\/strong> – Contains the drawing data of the piece<\/li>\n\n\n\n
- filename.PRN<\/strong> – Contains axis heights and bend data<\/li>\n<\/ul>\n\n\n\n
The files saved depend on how the programme was originally created.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/03\/image-18.png\")
<\/figure>\n\n\n\nSaving the Current Programme<\/h3>\n\n\n\n
To save the currently selected programme to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press the save key from the data settings mask if the programme is only NUMERIC<\/li>\n\n\n\n
- Press the save key from any SETTINGS, CALCULATE, or GRAPHIC EDITOR mask if the programme is graphic<\/li>\n<\/ul>\n\n\n\n
Saving Any Programme from SSD<\/h3>\n\n\n\n
To save any programme from SSD to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press to select the programme list<\/li>\n\n\n\n
- Move the cursor to the programme you wish to save<\/li>\n\n\n\n
- Press the save key<\/li>\n<\/ol>\n\n\n\n
Uploading a Programme from USB<\/h3>\n\n\n\n
To upload a programme from USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press to select the programme list<\/li>\n\n\n\n
- Press to select the list on USB device<\/li>\n\n\n\n
- Select the programme you wish to upload<\/li>\n\n\n\n
- Press the upload key: the programme copies from USB device to SSD<\/li>\n\n\n\n
- Press (list in SSD) to verify the programme appears<\/li>\n\n\n\n
- Select the programme and press [ENTER] to access the data<\/li>\n<\/ol>\n\n\n\n
Saving\/Uploading All Programmes<\/h3>\n\n\n\n
For comprehensive programme backup within ESA S875 Windows memory management:<\/p>\n\n\n\n
To save all programmes to USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press to select the programme list<\/li>\n\n\n\n
- Press the menu key and select [Save programmes<\/em>]<\/strong><\/li>\n\n\n\n
- All programmes will be saved to the USB device<\/li>\n<\/ol>\n\n\n\n
To upload all programmes from USB device:<\/strong><\/p>\n\n\n\n
- \n
- Press to select the programme list<\/li>\n\n\n\n
- Press to view the programme list on USB device<\/li>\n\n\n\n
- Press the menu key and select [Save programmes<\/em>]<\/strong><\/li>\n\n\n\n
- All programmes will be uploaded from the USB device<\/li>\n<\/ol>\n\n\n\n
Recommended Security Saving Practices<\/h2>\n\n\n\n
Proper ESA S875 Windows memory management includes regular security saving to protect against data loss. Security saving refers to storing on USB device the essential data that enables your press brake to operate.<\/p>\n\n\n\n
Parameters<\/strong><\/p>\n\n\n\n
Security saving of parameters should be carried out at the time of machine shipping. Any subsequent changes must be saved immediately after they are made. This ensures you always have a recoverable copy of your machine’s correct configuration.<\/p>\n\n\n\n
Programmes<\/strong><\/p>\n\n\n\n
Security saving of programmes should be performed periodically by the customer, depending on the number and importance of programmes created. For busy shops creating multiple new programs daily, more frequent backups are recommended as part of routine ESA S875 Windows memory management.<\/p>\n\n\n\n
Equipment<\/strong><\/p>\n\n\n\n
Security saving of equipment should be performed after inserting all customer tools. Additionally, save data every time a new punch or die is entered to maintain complete tooling records.<\/p>\n\n\n\n
By following these guidelines, you ensure that your valuable programming data, tooling definitions, and machine configurations remain safe and recoverable, minimizing downtime and protecting your productivity.<\/p>\n\n\n\n
Frequently Asked Questions(FAQ)<\/h2>\n\n\n
\n\n\nWhat is the difference between SSD and internal memory in ESA S875 Windows memory management?<\/h3>\n
\n\nIn\u00a0ESA S875 Windows memory management, the SSD (Flash Hard Disk) serves as permanent long-term storage for the operating system, application programme, and backup copies of machine data. The internal memory (buffered RAM) is working memory where data are temporarily stored during machine operation. Thanks to an internal battery, internal memory retains data even when powered off, but the SSD provides the primary permanent storage.<\/p>\n\n<\/div>\n<\/div>\n
\nHow often should I back up my machine parameters?<\/h3>\n
\n\nAccording to recommended\u00a0ESA S875 Windows memory management\u00a0practices, machine parameters should be backed up at the time of machine shipping and immediately after any changes are made. This ensures you always have a recoverable copy of your correct machine configuration in case of data corruption or accidental parameter changes.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n
Conclusion<\/h2>\n\n\n\n
Proper\u00a0ESA S875 Windows memory management\u00a0is essential for protecting your valuable bending programs, tooling definitions, and machine configurations. By understanding the different memory devices, regularly backing up data to USB, and following the recommended practices for saving and uploading various data types, you can prevent data loss and minimize downtime. Remember to maintain duplicate backups and save immediately after any parameter changes.<\/p>\n\n\n\n
For more detailed support on\u00a0ESA S875 Windows memory management\u00a0or any other questions about your HARSLE press brake, don’t hesitate to contact our technical support team. We’re here to help you keep your machine running efficiently and your data secure.<\/p>\n","protected":false},"excerpt":{"rendered":"
ESA S875 Windows memory management is a critical skill for any press brake operator or shop manager who wants to keep<\/p>","protected":false},"author":32,"featured_media":81592,"comment_status":"open","ping_status":"closed","template":"","meta":{"footnotes":""},"doc_category":[3249],"doc_tag":[5342,3379,5343],"knowledge_base":[3228],"class_list":["post-81198","docs","type-docs","status-publish","has-post-thumbnail","hentry","doc_category-system-operation","doc_tag-cnc-memory-optimization","doc_tag-esa-s875","doc_tag-file-management","knowledge_base-press-brake"],"year_month":"2026-05","word_count":1992,"total_views":"302","reactions":{"happy":"0","normal":"0","sad":"0"},"author_info":{"name":"Cristina","author_nicename":"christina","author_url":"https:\/\/www.harsle.com\/es\/author\/christina\/"},"doc_category_info":[{"term_name":"System Operation","term_url":"https:\/\/www.harsle.com\/es\/docs\/hydraulic-press\/system-operation\/"}],"doc_tag_info":[{"term_name":"CNC Memory Optimization","term_url":"https:\/\/www.harsle.com\/es\/docs-tag\/cnc-memory-optimization\/"},{"term_name":"ESA S875","term_url":"https:\/\/www.harsle.com\/es\/docs-tag\/esa-s875\/"},{"term_name":"File Management","term_url":"https:\/\/www.harsle.com\/es\/docs-tag\/file-management\/"}],"jetpack_sharing_enabled":true,"knowledge_base_info":[{"term_name":"Press Brake","term_url":"https:\/\/www.harsle.com\/es\/docs\/press-brake\/","term_slug":"press-brake"}],"knowledge_base_slug":["press-brake"],"_links":{"self":[{"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/docs\/81198","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/docs"}],"about":[{"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/types\/docs"}],"author":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/users\/32"}],"replies":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/comments?post=81198"}],"version-history":[{"count":0,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/docs\/81198\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/media\/81592"}],"wp:attachment":[{"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/media?parent=81198"}],"wp:term":[{"taxonomy":"doc_category","embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/doc_category?post=81198"},{"taxonomy":"doc_tag","embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/doc_tag?post=81198"},{"taxonomy":"knowledge_base","embeddable":true,"href":"https:\/\/www.harsle.com\/es\/wp-json\/wp\/v2\/knowledge_base?post=81198"}],"curies":[{"name":"gracias","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}
- All programmes will be uploaded from the USB device<\/li>\n<\/ol>\n\n\n\n
- All programmes will be saved to the USB device<\/li>\n<\/ol>\n\n\n\n
- filename.PRN<\/strong> – Contains axis heights and bend data<\/li>\n<\/ul>\n\n\n\n
- All tools will be uploaded from the USB device<\/li>\n<\/ol>\n\n\n\n
- All tools will be saved to the USB device<\/li>\n<\/ol>\n\n\n\n
- Press [Save All<\/em>]<\/strong> or [Upload All<\/em>]<\/strong><\/li>\n<\/ol>\n\n\n\n
- Press [Upload from Disk<\/em>]<\/strong> to load the file from USB device<\/li>\n<\/ol>\n\n\n\n
- Press the save key to save the file containing the data to the USB device<\/li>\n<\/ol>\n\n\n\n
- Global Uploading<\/strong>: From Configure Machine Menu (2), press [Upload All<\/em>]<\/strong><\/li>\n<\/ul>\n\n\n\n
- UPLOADING<\/strong>: Transferring data from USB device to internal memory<\/li>\n<\/ul>\n\n\n\n
- SAVING<\/strong>: Transferring data from internal memory to USB device<\/li>\n\n\n\n
- Axis parameters<\/strong> (Menu option 1) – calibration and movement characteristics<\/li>\n\n\n\n