{"id":88584,"date":"2026-08-28T02:56:23","date_gmt":"2026-08-28T02:56:23","guid":{"rendered":"https:\/\/www.harsle.com\/?post_type=docs&#038;p=88584"},"modified":"2026-08-28T02:56:27","modified_gmt":"2026-08-28T02:56:27","password":"","slug":"estun-e315p-valve-settings","status":"publish","type":"docs","link":"https:\/\/www.harsle.com\/pl\/docs\/estun-e315p-valve-settings\/","title":{"rendered":"How to Adjust ESTUN E315P Valve Settings Correctly?"},"content":{"rendered":"<p class=\"wp-block-paragraph\">Correct ESTUN E315P Valve Settings are essential for coordinating the controller&#8217;s output signals with different operations during the press brake bending cycle. Through the Valve Configuration interface, technicians can assign YV1\u2013YV7 outputs to specific bending operations according to the machine&#8217;s hydraulic and electrical configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When a configured operation becomes active, the E315P sets the corresponding output or outputs to HIGH. Since one operation can activate multiple outputs simultaneously, technicians must configure each assignment carefully. This guide explains how to access, adjust, and verify ESTUN E315P Valve Settings using the controller&#8217;s Valve Configuration interface.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Are ESTUN E315P Valve Settings?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The ESTUN E315P Valve Settings define which YV outputs are activated during specific press brake operations.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The Valve Configuration interface displays the bending operations in the left column and the available outputs <strong>YV1 through YV7<\/strong> across the configuration area.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Technicians can use this interface to establish the required relationship between a bending operation and its corresponding output signals.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When a particular operation is executed, the E315P changes the assigned outputs to HIGH according to the configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Because these outputs are part of the machine control sequence, their assignments should correspond with the actual machine design rather than being changed arbitrarily.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Access the Valve Configuration?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Before adjusting the valve assignments, technicians must first enter the appropriate parameter interface.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Obtain Level 1 Permission<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The Valve Configuration function requires <strong>Level 1 permission<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Complete the required authentication before entering the machine parameter settings. This prevents normal operators from unintentionally modifying important machine configuration parameters.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Open Machine Parameters<\/h3>\n\n\n\n<figure class=\"wp-block-image aligncenter size-full is-resized\"><img decoding=\"async\" width=\"449\" height=\"236\" src=\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15.png\" alt=\"ESTUN E315P Valve Settings\" class=\"wp-image-88602\" style=\"width:556px;height:auto\" srcset=\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15.png 449w, https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15-400x210.png 400w, https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15-18x9.png 18w, https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15-360x189.png 360w, https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15-430x226.png 430w, https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/08\/image-15-148x78.png 148w\" sizes=\"(max-width: 449px) 100vw, 449px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">After obtaining the required permission, enter the <strong>Machine Parameters<\/strong> interface.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">From this area, select <strong>Valve Configuration<\/strong> to open the valve setting screen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The configuration page displays the available bending operations together with YV1\u2013YV7.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Image summary:<\/strong> The E315P Valve Configuration screen allows technicians to assign YV1\u2013YV7 outputs to different bending operations.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Adjust ESTUN E315P Valve Settings?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Once the Valve Configuration page is open, the required outputs can be assigned to each operation.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Select the Required Operation<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">First, identify the bending operation that needs to be configured.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The interface lists the available operations in the left column. Select the appropriate operation before changing any output assignment.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Each row represents a particular stage or function in the machine operating sequence.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Assign the Required YV Outputs<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After selecting the operation, choose the corresponding outputs from <strong>YV1 to YV7<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When an output is enabled for a particular operation, the controller will set that output HIGH while the specified operation is active.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The exact YV combination depends on the actual machine configuration. Therefore, ESTUN E315P Valve Settings should always be matched with the machine&#8217;s electrical and hydraulic design.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Do not copy another machine&#8217;s YV configuration unless its control system and hydraulic configuration are confirmed to be identical.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Confirm the Changes<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After selecting the required outputs, press <strong>Potwierdza\u0107<\/strong> to apply the configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Before returning the machine to normal operation, verify that the selected YV outputs correspond to the intended operation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If several settings have been changed, checking them individually can make it easier to identify an incorrect assignment.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Can Multiple YV Outputs Work Together?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Yes. The E315P allows <strong>multiple output ports to be activated simultaneously for one operation<\/strong> when required by the machine configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, a particular bending stage may require more than one output signal to become active at the same time.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In this case, technicians can enable multiple YV outputs in the same operation row.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This function makes the ESTUN E315P Valve Settings flexible enough to accommodate different machine control requirements.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, the number and combination of outputs should always follow the specific machine configuration.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Configure the Dwell Operation<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The E315P manual provides a Dwell operation as an example of valve configuration.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Select the Dwell Row<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Enter the Valve Configuration interface and locate the <strong>Mieszka\u0107<\/strong> dzia\u0142anie.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This row represents the output configuration used during the corresponding dwell stage of the bending sequence.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Enable YV3 and YV4<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">In the manual example, <strong>YV3 and YV4<\/strong> are enabled for the Dwell operation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When this operation becomes active, the controller therefore sets the corresponding configured outputs HIGH.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is an example configuration used to demonstrate the setting procedure. Actual valve assignments should follow the configuration of the specific press brake.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Confirm the Configuration<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After enabling the required outputs, select <strong>Potwierd\u017a zmiany<\/strong> to apply the settings.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Technicians should then verify the configuration before normal machine operation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Image summary:<\/strong> In the manual configuration example, YV3 and YV4 are enabled simultaneously for the Dwell operation.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Why Should Valve Settings Match the Machine?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The ESTUN E315P Valve Settings form part of the relationship between the CNC controller and the machine&#8217;s operating sequence.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Incorrect assignments may cause the controller to activate an unintended output or fail to activate the required output during a specific operation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For this reason, technicians should not determine YV assignments based only on the names displayed on the screen.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Before changing the configuration, compare the controller settings with:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Machine electrical diagrams<\/li>\n\n\n\n<li>Hydraulic system requirements<\/li>\n\n\n\n<li>Existing parameter records<\/li>\n\n\n\n<li>Actual machine configuration<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This is particularly important when restoring parameters, replacing a controller, or commissioning a machine.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Should You Check Before Adjusting Valve Settings?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Before modifying <strong>ESTUN E315P Valve Settings<\/strong>, record the existing configuration and confirm which operation requires adjustment.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Technicians should check:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The current YV1\u2013YV7 assignments<\/li>\n\n\n\n<li>The operation being modified<\/li>\n\n\n\n<li>The required output combination<\/li>\n\n\n\n<li>The machine electrical diagram<\/li>\n\n\n\n<li>The hydraulic control configuration<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Avoid changing several unrelated valve assignments during troubleshooting. If multiple parameters are modified at the same time, identifying the cause of an abnormal machine response can become more difficult.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It is better to make the required adjustment, confirm it, and then check the corresponding machine operation.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Best Practices for ESTUN E315P Valve Settings<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Reliable ESTUN E315P Valve Settings depend on correctly matching each bending operation with the required YV outputs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Always obtain the appropriate permission before entering Valve Configuration, record the original settings, and verify the machine documentation before making changes.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Remember that the E315P can activate multiple YV outputs simultaneously for a single operation. Therefore, technicians should check the complete output combination rather than focusing on only one YV signal.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After completing the configuration, confirm the changes and verify the corresponding operation carefully. Following this process helps maintain consistent control between the E315P controller and the press brake operating sequence.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Cz\u0119sto zadawane pytania (FAQ)<\/h2>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-1787815673195\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">What Permission Is Required for Valve Configuration?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>According to the E315P manual, <strong>Level 1 permission<\/strong> is required to access the Machine Parameters interface and adjust Valve Configuration.<br \/>This helps prevent unintended changes to important machine control parameters.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-1787818925581\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Can Multiple YV Outputs Be Activated Together?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Yes. <strong>ESTUN E315P Valve Settings<\/strong> allow multiple output ports to be assigned to the same operation.<br \/>When that operation is active, the corresponding configured outputs can become HIGH simultaneously.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-1787818933739\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">What Should I Check Before Changing Valve Settings?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Before making changes, check the existing YV assignments, electrical schematic, hydraulic configuration, and required bending operation.<br \/>It is also recommended to record the original settings so they can be restored if necessary.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">Wniosek<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Correct <a href=\"https:\/\/www.youtube.com\/watch?v=GwlCHLs7I6U&amp;t=126s\" data-type=\"link\" data-id=\"https:\/\/www.youtube.com\/watch?v=GwlCHLs7I6U&amp;t=126s\" target=\"_blank\" rel=\"noopener\">ESTUN E315P<\/a> Valve Settings establish the required relationship between bending operations and YV1\u2013YV7 output signals. The E315P allows technicians to assign individual or multiple outputs to an operation according to the specific <a href=\"https:\/\/www.harsle.com\/pl\/docs\/press-brake-zero-drift\/\" data-type=\"link\" data-id=\"https:\/\/www.harsle.com\/docs\/press-brake-zero-drift\/\">prasa kraw\u0119dziowa<\/a> configuration.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When adjusting these settings, obtain Level 1 permission, record the original configuration, verify the electrical and hydraulic documentation, and confirm each change carefully. The YV3 and YV4 Dwell configuration shown in the manual should be understood as an example rather than a universal setting.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">By configuring ESTUN E315P Valve Settings according to the actual machine design, technicians can maintain reliable coordination between the CNC controller and the press brake operating sequence.<\/p>","protected":false},"excerpt":{"rendered":"<p>Correct ESTUN E315P Valve Settings are essential for coordinating the controller&#8217;s output signals with different operations during the press brake<\/p>","protected":false},"author":32,"featured_media":88601,"comment_status":"open","ping_status":"closed","template":"","meta":{"footnotes":""},"doc_category":[3249],"doc_tag":[3549,5631,5990],"knowledge_base":[3228],"class_list":["post-88584","docs","type-docs","status-publish","has-post-thumbnail","hentry","doc_category-system-operation","doc_tag-advanced-bending-technology","doc_tag-e315p-press-brake-controller","doc_tag-valve-settings-e315p-press-brake-controller","knowledge_base-press-brake"],"year_month":"2026-08","word_count":1290,"total_views":0,"reactions":{"happy":0,"normal":0,"sad":0},"author_info":{"name":"Krystyna","author_nicename":"christina","author_url":"https:\/\/www.harsle.com\/pl\/author\/christina\/"},"doc_category_info":[{"term_name":"System Operation","term_url":"https:\/\/www.harsle.com\/pl\/docs\/hydraulic-press\/system-operation\/"}],"doc_tag_info":[{"term_name":"Advanced Bending Technology","term_url":"https:\/\/www.harsle.com\/pl\/docs-tag\/advanced-bending-technology\/"},{"term_name":"E315P press brake controller","term_url":"https:\/\/www.harsle.com\/pl\/docs-tag\/e315p-press-brake-controller\/"},{"term_name":"Valve Settings","term_url":"https:\/\/www.harsle.com\/pl\/docs-tag\/valve-settings-e315p-press-brake-controller\/"}],"jetpack_sharing_enabled":true,"knowledge_base_info":[{"term_name":"Press Brake","term_url":"https:\/\/www.harsle.com\/pl\/docs\/press-brake\/","term_slug":"press-brake"}],"knowledge_base_slug":["press-brake"],"_links":{"self":[{"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/docs\/88584","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/docs"}],"about":[{"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/types\/docs"}],"author":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/users\/32"}],"replies":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/comments?post=88584"}],"version-history":[{"count":0,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/docs\/88584\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/media\/88601"}],"wp:attachment":[{"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/media?parent=88584"}],"wp:term":[{"taxonomy":"doc_category","embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/doc_category?post=88584"},{"taxonomy":"doc_tag","embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/doc_tag?post=88584"},{"taxonomy":"knowledge_base","embeddable":true,"href":"https:\/\/www.harsle.com\/pl\/wp-json\/wp\/v2\/knowledge_base?post=88584"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}