![\"ESTUN](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/10\/ESTUN-E315P\u89d2\u5ea6\u7f16\u7a0b\u6307\u5357-1200x800.png\")
<\/figure>\n\n\n\nWhat Are the Four Essential Parameters?<\/h2>\n\n\n\n
According to Section 5.11 of the E315P commissioning guide, four parameters are required for automatic bending angle calculation.<\/p>\n\n\n\n Each parameter provides different information for ESTUN E315P Angle Programming.<\/p>\n\n\n\n The following sections explain their individual functions and why they should be verified before bending.<\/p>\n\n\n\n The lower die is one of the essential components affecting bending geometry.<\/p>\n\n\n\n During ESTUN E315P Angle Programming, the controller uses the technical parameters configured for the selected die.<\/p>\n\n\n\n To configure the die information, access:<\/p>\n\n\n\n Programming Constants \u2192 Die Setup<\/p>\n\n\n\n The parameters should correspond to the actual lower die installed on the machine.<\/p>\n\n\n\n Different lower dies can have different geometric characteristics. Therefore, selecting a die configuration that does not match the installed tooling may affect the calculated bending requirements.<\/p>\n\n\n\n Before programming the bending angle, operators should confirm that the correct die has been installed and that its corresponding technical information has been configured.<\/p>\n\n\n\n If the lower die is replaced, the die setup should be reviewed before continuing with angle-based programming.<\/p>\n\n\n\n Sheet Thickness is another essential parameter used during bending angle calculation.<\/p>\n\n\n\n The E315P commissioning guide requires operators to enter the actual thickness of the processed sheet in the Single-Step or Multi-Step programming interface.<\/p>\n\n\n\n This value should represent the workpiece being bent.<\/p>\n\n\n\n For example, if the actual sheet thickness differs from the value entered into the controller, the system performs its calculation using information that does not accurately represent the workpiece.<\/p>\n\n\n\n This can affect the resulting bending operation.<\/p>\n\n\n\n When preparing ESTUN E315P Angle Programming, technicians should therefore verify the actual sheet thickness before entering the corresponding value.<\/p>\n\n\n\n If different workpieces are processed using the same machine, the thickness setting should be checked whenever the material specifications change.<\/p>\n\n\n\n Accurate thickness information provides an essential basis for the controller’s automatic bending calculations.<\/p>\n\n\n\n Different materials respond differently to bending forces.<\/p>\n\n\n\n The E315P controller uses material information during its bending calculations. Therefore, the correct material must be selected when preparing an angle-based program.<\/p>\n\n\n\n The commissioning guide specifies that the selected material must have its properties configured in advance in the Material Table.<\/p>\n\n\n\n The E315P material setup includes two important properties:<\/p>\n\n\n\n These properties describe aspects of the material’s mechanical behavior.<\/p>\n\n\n\n Because different materials have different mechanical characteristics, incorrect material selection may affect the bending calculation.<\/p>\n\n\n\n For reliable ESTUN E315P Angle Programming, operators should confirm that the selected material corresponds with the actual sheet and that the material parameters have been configured appropriately.<\/p>\n\n\n\n If the required material is not correctly configured, its properties should be reviewed in the Material Table before proceeding.<\/p>\n\n\n\n Clamping Point Teaching is a critical prerequisite for bending angle accuracy.<\/p>\n\n\n\n According to the commissioning guide, Clamping Point Correction must be performed to calibrate the relevant position values.<\/p>\n\n\n\n The clamping point establishes an important positional relationship between the upper and lower tooling.<\/p>\n\n\n\n If this relationship is inaccurate, the controller may use incorrect positional information when calculating the bending operation.<\/p>\n\n\n\n During ESTUN E315P Angle Programming, the clamping point information should therefore correspond with the actual machine configuration.<\/p>\n\n\n\n The E315P provides teaching and correction functions that allow technicians to establish and adjust the clamping point relationship.<\/p>\n\n\n\n Before relying on automatic bending angle calculations, confirm that the required clamping point teaching and correction procedures have been completed.<\/p>\n\n\n\n This is especially important after changes that affect the tooling position or the machine’s positional reference.<\/p>\n\n\n\n Before creating an angle-based bending program, technicians should verify the four essential parameters systematically.<\/p>\n\n\n\n Check the installed lower die and verify that its technical parameters correspond with the configuration in Programming Constants \u2192 Die Setup.<\/p>\n\n\n\n Open the Single-Step or Multi-Step programming interface and enter the actual thickness of the workpiece.<\/p>\n\n\n\n Choose the material corresponding to the sheet being processed.<\/p>\n\n\n\n Confirm that the required material properties have already been configured in the Material Table.<\/p>\n\n\n\n Check that Clamping Point Teaching and the necessary correction have been completed.<\/p>\n\n\n\n Once these conditions are satisfied, the controller has the essential information identified in the manual for automatic angle calculation.<\/p>\n\n\n\n This preparation helps establish a more reliable foundation for ESTUN E315P Angle Programming.<\/p>\n\n\n\n If the actual bending angle differs from the programmed value, the four essential parameters should be reviewed before making unrelated adjustments.<\/p>\n\n\n\n First, check whether the configured lower die matches the installed tooling.<\/p>\n\n\n\n Next, verify that the programmed Sheet Thickness corresponds with the actual workpiece.<\/p>\n\n\n\n Then confirm that the correct material has been selected and that its predefined properties are appropriate.<\/p>\n\n\n\n Finally, review the Clamping Point Teaching and correction status.<\/p>\n\n\n\n These checks help identify whether the bending calculation is based on incorrect machine or workpiece information.<\/p>\n\n\n\n Although other mechanical and operating conditions can also influence actual bending results, the E315P commissioning guide specifically identifies these four parameters as mandatory for angle calculation.<\/p>\n\n\n\n Reliable ESTUN E315P Angle Programming begins with accurate machine and workpiece information.<\/p>\n\n\n\n The controller can perform automatic bending calculations, but the quality of those calculations depends on the parameters provided.<\/p>\n\n\n\n Die Setup establishes the relevant tooling information, Sheet Thickness describes the workpiece dimension, Material Setup provides the required mechanical properties, and Clamping Point Teaching calibrates the positional relationship.<\/p>\n\n\n\n By checking these four parameters before programming and reviewing them whenever the tooling or workpiece changes, operators can reduce errors caused by incorrect configuration.<\/p>\n\n\n\n This systematic approach supports more consistent bending results and provides a practical basis for troubleshooting angle-related problems during E315P press brake operation.<\/p>\n\n\n\n Yes. If the replacement lower die has different technical specifications, the corresponding information should be updated in Programming Constants \u2192 Die Setup. Using parameters from a different die may affect automatic angle calculations.<\/p>\n\n<\/div>\n<\/div>\n The program should be reviewed before processing a different material. Even when sheet thickness and the required bending angle remain unchanged, different materials may have different mechanical properties. Select the correct material and verify its parameters before running the program.<\/p>\n\n<\/div>\n<\/div>\n Not necessarily. The commissioning guide identifies Clamping Point Correction as a prerequisite for accurate angle calculation, but it does not require repeating the procedure before every bending cycle. The calibration should be checked when the machine’s positional relationship changes or when a relevant positioning error is suspected.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n Accurate ESTUN E315P Angle Programming depends on four essential parameters: Configura\u00e7\u00e3o de matriz<\/a>, Sheet Thickness, Material Properties, and Clamping Point Teaching. Together, these settings provide the controller with the tooling, workpiece, and positional information required for automatic bending angle calculations.<\/p>\n\n\n\n Before starting production, operators should confirm that the installed lower die matches its configured parameters, the actual sheet thickness is entered correctly, and the appropriate material properties are selected. Clamping Point Correction should also be completed to establish the required positional relationship.<\/p>\n\n\n\nPar\u00e2metro<\/th> Configuration Requirement<\/th><\/tr> Morrer<\/td> Configure technical parameters according to the actual lower die<\/td><\/tr> Espessura da folha<\/td> Enter the actual workpiece thickness<\/td><\/tr> Material<\/td> Select the corresponding material with predefined properties<\/td><\/tr> Clamping Point Teaching<\/td> Perform clamping point correction to calibrate position values<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n How Does Die Setup Affect Angle Programming?<\/h2>\n\n\n\n
Why Is Sheet Thickness Important?<\/h2>\n\n\n\n
How Do Material Properties Affect Bending Angles?<\/h2>\n\n\n\n
\n
What Is the Role of Clamping Point Teaching?<\/h2>\n\n\n\n
How to Prepare for Angle Programming<\/h2>\n\n\n\n
Step 1: Confirm the Lower Die<\/h3>\n\n\n\n
Step 2: Enter the Actual Sheet Thickness<\/h3>\n\n\n\n
Step 3: Select the Correct Material<\/h3>\n\n\n\n
Step 4: Verify Clamping Point Correction<\/h3>\n\n\n\n
What Causes Inaccurate Bending Angles?<\/h2>\n\n\n\n
Improving Angle Programming Accuracy<\/h2>\n\n\n\n
Perguntas frequentes (FAQ)<\/h2>\n\n\n
Should Die Parameters Be Updated After Changing the Lower Die?<\/h3>\n
Can the Same Bending Program Be Used for Different Materials?<\/h3>\n
Does Clamping Point Correction Need to Be Performed Before Every Bend?<\/h3>\n
Conclus\u00e3o<\/h2>\n\n\n\n