| Par\u00e2metro<\/th> | Especifica\u00e7\u00e3o<\/th><\/tr> |
|---|---|
| Parameter Name<\/td> | X-Correction<\/td><\/tr> |
| Default Value<\/td> | Habilitar<\/td><\/tr> |
| Available Options<\/td> | Enable \/ Disable<\/td><\/tr> |
| Fun\u00e7\u00e3o<\/td> | Controls internal and external dimension selection during workstep programming<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n The default setting is Enable.<\/p>\n\n\n\n Unlike an axis calibration parameter, X-Correction relates to the dimensional reference used when preparing bending operations.<\/p>\n\n\n\n The manual does not provide a detailed correction formula or specify an automatic mechanical compensation procedure for this parameter.<\/p>\n\n\n\n Therefore, operators should understand its programming purpose before making adjustments.<\/p>\n\n\n\n The ESTUN E315P X-Correction is relevant when operators define dimensions for individual bending worksteps.<\/p>\n\n\n\n In sheet metal fabrication, dimensions may be specified using different reference surfaces depending on the drawing and bending requirements.<\/p>\n\n\n\n For example, a finished component may have dimensions measured along its internal surfaces or external surfaces.<\/p>\n\n\n\n These measurements are not necessarily identical because the sheet metal has a physical thickness and the finished bend has a specific geometry.<\/p>\n\n\n\n When preparing a bending program, operators should identify which dimensional reference corresponds to the engineering drawing.<\/p>\n\n\n\n An internal dimension generally refers to a measurement based on the inside surfaces of a formed sheet metal component.<\/p>\n\n\n\n This reference may be used when the drawing specifies internal clearances or dimensions between inside faces.<\/p>\n\n\n\n An external dimension generally refers to a measurement based on the outside surfaces of the formed component.<\/p>\n\n\n\n This reference may be used when the drawing specifies overall external dimensions.<\/p>\n\n\n\n The ESTUN E315P X-Correction parameter is associated with selecting between these dimensional references during programming.<\/p>\n\n\n\n However, the exact relationship between this setting and the controller’s numerical calculations should be verified against the applicable controller software and machine configuration.<\/p>\n\n\n\n Before changing the parameter, confirm that the intended bending program and dimensional requirements are understood.<\/p>\n\n\n\n Open the E315P controller’s parameter settings.<\/p>\n\n\n\n Locate the C.1 Constants<\/strong> section described in the operating manual.<\/p>\n\n\n\n Find the parameter labeled X-Correction<\/strong>.<\/p>\n\n\n\n Review whether the parameter is currently set to Enable or Disable.<\/p>\n\n\n\n According to the manual, Enable is the default value.<\/p>\n\n\n\n If the machine has already been commissioned and operates normally, record the existing configuration before making changes.<\/p>\n\n\n\n Choose the required setting according to the programming requirements.<\/p>\n\n\n\n Enable:<\/strong> Activates the X-Correction option associated with internal and external dimension selection.<\/p>\n\n\n\n Disable:<\/strong> Disables this option.<\/p>\n\n\n\n The manual identifies these two choices but does not provide sufficient detail to establish every resulting calculation or interface behavior.<\/p>\n\n\n\n For this reason, operators should avoid assuming that changing the parameter automatically recalibrates the backgauge.<\/p>\n\n\n\n After changing the ESTUN E315P X-Correction, review the relevant bending workstep.<\/p>\n\n\n\n Confirm that the intended dimensional reference is available and correctly selected.<\/p>\n\n\n\n Check the programmed X-axis values against the engineering drawing and the required bending dimensions.<\/p>\n\n\n\n Before production, verify the machine’s positioning behavior under appropriate safe operating conditions.<\/p>\n\n\n\n Understanding the difference between internal and external dimensions is essential when using dimensional references in bending programs.<\/p>\n\n\n\n Consider a simple sheet metal component with a 90-degree bend.<\/p>\n\n\n\n The internal dimension is measured using the inside surfaces of the formed part, while the external dimension is measured using its outside surfaces.<\/p>\n\n\n\n Because the material has thickness, these measurements may differ.<\/p>\n\n\n\n The relationship also depends on the component geometry and the specific measurement points.<\/p>\n\n\n\n For this reason, operators should not assume that converting between internal and external dimensions always involves adding or subtracting one sheet thickness.<\/p>\n\n\n\n The correct interpretation depends on the engineering drawing and bending geometry.<\/p>\n\n\n\n When using the ESTUN E315P X-Correction, the dimensional reference should be consistent with the drawing requirements.<\/p>\n\n\n\n Incorrect interpretation of the reference may lead to unsuitable programmed dimensions even when the machine’s mechanical positioning system operates normally.<\/p>\n\n\n\n No. These functions should be distinguished.<\/p>\n\n\n\n X-axis calibration concerns the relationship between the actual backgauge position and the position recognized by the controller.<\/p>\n\n\n\n It may involve reference positioning, axis teaching, or other machine-specific commissioning procedures.<\/p>\n\n\n\n By comparison, the ESTUN E315P X-Correction parameter is associated with internal and external dimension selection during workstep programming.<\/p>\n\n\n\n Changing this parameter should not be treated as a substitute for correcting mechanical alignment, reference-position errors, or servo positioning faults.<\/p>\n\n\n\n If the backgauge does not reach its commanded position, operators should investigate the relevant axis settings and mechanical conditions rather than relying on X-Correction alone.<\/p>\n\n\n\n Internal and external dimensions refer to different measurement surfaces.<\/p>\n\n\n\n Operators should confirm the intended reference before entering bending dimensions.<\/p>\n\n\n\n The parameter is not documented as a general-purpose mechanical accuracy correction.<\/p>\n\n\n\n Unexpected backgauge positioning should be investigated separately.<\/p>\n\n\n\n The default setting is Enable, but an existing machine may have been configured for specific operating requirements.<\/p>\n\n\n\n Record the current setting before making changes.<\/p>\n\n\n\n After adjusting the ESTUN E315P X-Correction, operators should review the programmed dimensions and confirm that the intended reference is being used.<\/p>\n\n\n\n A configuration change should not be accepted without checking its effect on the relevant program.<\/p>\n\n\n\n |
![\"ESTUN](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/11\/ESTUN-E315P-X\u6821\u6b63\u64cd\u4f5c\u6307\u5357-1200x800.png\")
<\/figure>\n\n\n\n