![\"ESA](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/04\/image-40.png\")
<\/figure>\n\n\n\n- \n
- \u0413\u043b\u0430\u0432\u043d\u043e\u0435 \u043e\u043a\u043d\u043e<\/strong>: Shows the machine structure, punch and die, and the workpiece before and after bending<\/li>\n\n\n\n
- Orientation Window<\/strong>: Indicates how to position or rotate the sheet for each bend<\/li>\n\n\n\n
- \u041e\u043a\u043d\u043e \u0434\u0430\u043d\u043d\u044b\u0445<\/strong>: Displays bending data, piece counter, and sheet development<\/li>\n<\/ul>\n\n\n\n
This visual guidance helps operators clearly understand each bending step and reduces setup errors.<\/p>\n\n\n\n
Step 3: Using the Automatic Numeric Page<\/h3>\n\n\n\n
For numeric programs, the automatic page displays axis positions along with program data. Note that program parameters cannot be modified in ESA S650 Automatic Mode.<\/p>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/04\/image-41.png\")
<\/figure>\n\n\n\n![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/04\/image-42.png\")
<\/figure>\n\n\n\nTo improve visibility, operators can enlarge the display to show axis values more clearly, which is useful during production monitoring.<\/p>\n\n\n\n
Step-by-Step Guide to Running Programs in ESA S650 Automatic Mode<\/h2>\n\n\n\n
Step 4: Starting the Automatic Cycle<\/h3>\n\n\n\n
To start execution:<\/p>\n\n\n\n
- \n
- \u041d\u0430\u0436\u043c\u0438\u0442\u0435 \u043a\u043d\u043e\u043f\u043a\u0443 \u041d\u0410\u0427\u0418\u041d\u0410\u0422\u042c<\/strong> \u043a\u043d\u043e\u043f\u043a\u0430<\/li>\n\n\n\n
- The system will automatically position the back-gauge axes<\/li>\n\n\n\n
- Press the down pedal to move the ram and perform the bend<\/li>\n<\/ul>\n\n\n\n
After each bend, the ram returns automatically, and the system repositions for the next step. This cycle continues until all bends are completed.<\/p>\n\n\n\n
Step 5: Continuous Production Cycle<\/h3>\n\n\n\n
Once the final bend is completed, the ESA S650 Automatic Mode will restart the cycle from the first bend. This allows continuous production without manual intervention, significantly improving efficiency.<\/p>\n\n\n\n
Step 6: Viewing the First Bend<\/h3>\n\n\n\n
Operators can select the \u041f\u0435\u0440\u0432\u044b\u0439 \u0438\u0437\u0433\u0438\u0431<\/strong> function to quickly return to the initial step. This is useful for setup verification or restarting production from the beginning.<\/p>\n\n\n\n
Optimizing ESA S650 Automatic Mode with Sample Piece Execution<\/h2>\n\n\n\n
Step 7: Running a Sample Piece for Accuracy<\/h3>\n\n\n\n
Since CNC calculations are theoretical, it is recommended to produce a sample piece before full production. This can be done using semi-automatic mode, where each bend is executed step by step without advancing automatically.<\/p>\n\n\n\n
This method allows operators to verify and adjust bending accuracy before switching to full automatic production.<\/p>\n\n\n\n
Step 8: Measuring and Adjusting Bending Results<\/h3>\n\n\n\n
After performing a bend:<\/p>\n\n\n\n
- \n
- Measure the angle and length of the bend<\/li>\n\n\n\n
- Compare with the required specifications<\/li>\n\n\n\n
- If deviations exist, enter correction data in the system<\/li>\n<\/ul>\n\n\n\n
Corrections can be applied at three levels:<\/p>\n\n\n\n
- \n
- \u0423\u0440\u043e\u0432\u0435\u043d\u044c \u0434\u0435\u0442\u0430\u043b\u0438<\/strong> (all bends)<\/li>\n\n\n\n
- \u0423\u0440\u043e\u0432\u0435\u043d\u044c \u0440\u0430\u0437\u0434\u0435\u043b\u0430<\/strong><\/li>\n\n\n\n
- Single bend level<\/strong><\/li>\n<\/ul>\n\n\n\n
ESA S650 Automatic Mode Correction Settings<\/h2>\n\n\n\n
Step 9: Entering Correction Data<\/h3>\n\n\n\n
![\"\"](\"https:\/\/www.harsle.com\/wp-content\/uploads\/2026\/04\/image-43.png\")
<\/figure>\n\n\n\nCorrection values are entered as:<\/p>\n\n\n\n
- \n
- Angle corrections<\/strong> in degrees<\/li>\n\n\n\n
- Back-gauge position corrections<\/strong> in millimeters<\/li>\n<\/ul>\n\n\n\n
\u041f\u0440\u0438\u043c\u0435\u0440\u044b:<\/p>\n\n\n\n
- \n
- If the bend angle is too closed, enter a positive correction value<\/li>\n\n\n\n
- If the bend is too open, enter a negative value<\/li>\n\n\n\n
- If the bend length is too short, increase the X-axis value<\/li>\n\n\n\n
- If too long, decrease the X-axis value<\/li>\n<\/ul>\n\n\n\n
These corrections are automatically added to the existing program values.<\/p>\n\n\n\n
Step 10: Applying and Verifying Corrections<\/h3>\n\n\n\n
After entering correction data:<\/p>\n\n\n\n
- \n
- Confirm the correction<\/li>\n\n\n\n
- Reposition the back-gauge axes<\/li>\n\n\n\n
- Repeat the bending step<\/li>\n\n\n\n
- Check if the result meets requirements<\/li>\n<\/ul>\n\n\n\n
Repeat this process until all bends are accurate. Once completed, the automatic cycle can resume from the selected step.<\/p>\n\n\n\n
Step 11: Deleting Correction Data<\/h3>\n\n\n\n
If needed, correction values can be reset by selecting the Undo Correction<\/strong> function. This restores the original program values, allowing operators to restart adjustments if necessary.<\/p>\n\n\n\n
Key Tips for Efficient ESA S650 Automatic Mode Operation<\/h2>\n\n\n\n
\u041f\u043e\u0432\u044b\u0448\u0435\u043d\u0438\u0435 \u044d\u0444\u0444\u0435\u043a\u0442\u0438\u0432\u043d\u043e\u0441\u0442\u0438 \u043f\u0440\u043e\u0438\u0437\u0432\u043e\u0434\u0441\u0442\u0432\u0430<\/h3>\n\n\n\n
To maximize efficiency in ESA S650 Automatic Mode, always verify the program before execution and use sample pieces for calibration. This reduces errors during mass production.<\/p>\n\n\n\n
Avoiding Common Operational Errors<\/h3>\n\n\n\n
Follow these best practices:<\/p>\n\n\n\n
- \n
- Do not attempt to modify program data in automatic mode<\/li>\n\n\n\n
- Always check back-gauge positioning before starting<\/li>\n\n\n\n
- Apply corrections gradually and verify results step by step<\/li>\n\n\n\n
- Use graphic view for better visualization when available<\/li>\n<\/ul>\n\n\n\n
By following these guidelines, operators can ensure smooth operation, reduce downtime, and achieve consistent bending quality.<\/p>\n\n\n\n
\u0427\u0430\u0441\u0442\u043e \u0437\u0430\u0434\u0430\u0432\u0430\u0435\u043c\u044b\u0435 \u0432\u043e\u043f\u0440\u043e\u0441\u044b (FAQ)<\/h2>\n\n\n
\n\n\nCan I edit program data in ESA S650 Automatic Mode?<\/h3>\n
\n\nNo, program data cannot be modified while in ESA S650 Automatic Mode<\/strong>. Any adjustments must be made in editing or semi-automatic mode before running the program automatically.<\/p>\n\n<\/div>\n<\/div>\n
\nWhy should I run a sample piece before full production?<\/h3>\n
\n\nRunning a sample piece helps verify bending accuracy since system calculations are theoretical. It allows you to identify deviations and apply corrections before mass production begins.<\/p>\n\n<\/div>\n<\/div>\n
\nHow do I correct bending errors in ESA S650 Automatic Mode?<\/h3>\n
\n\nYou can measure the bend angle and length, then input correction values into the system. Corrections can be applied to the entire piece, specific sections, or individual bends to improve accuracy.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n
\u0417\u0430\u043a\u043b\u044e\u0447\u0435\u043d\u0438\u0435<\/h2>\n\n\n\n
Using ESA S650 Automatic Mode correctly is key to achieving efficient and consistent press brake production. By following the proper steps\u2014preparing the program, understanding the interface, executing the automatic cycle, and applying corrections when needed\u2014operators can ensure smooth and reliable operation.<\/p>\n\n\n\n
Running a sample piece and making precise adjustments before full production helps minimize errors and improves overall bending quality. Consistent monitoring and proper use of correction functions further enhance performance and reduce downtime.<\/p>\n\n\n\n
- Back-gauge position corrections<\/strong> in millimeters<\/li>\n<\/ul>\n\n\n\n
- \u0423\u0440\u043e\u0432\u0435\u043d\u044c \u0440\u0430\u0437\u0434\u0435\u043b\u0430<\/strong><\/li>\n\n\n\n
- \u0423\u0440\u043e\u0432\u0435\u043d\u044c \u0434\u0435\u0442\u0430\u043b\u0438<\/strong> (all bends)<\/li>\n\n\n\n
- Orientation Window<\/strong>: Indicates how to position or rotate the sheet for each bend<\/li>\n\n\n\n