Dokumentationszentrum
Umfassende technische Handbücher und Anleitungen, die Ihnen helfen, HARSLE-Maschinen zu beherrschen und Ihre Metallbearbeitungseffizienz zu optimieren
Beliebte Suche
Handbuchdelem daLaserdrückendelem
Wie beherrscht man die manuelle Bewegungssteuerung des HS-15T?
When it comes to harnessing the full potential of the HS-15T press machine, mastering the HS-15T Manual Movement controls is essential. This guide aims to directly address your need for understanding these manual controls and how they can significantly enhance your operational efficiency. By delving into the step-by-step processes of navigating machine status pages and configuring axis reference points, I will provide you with the insights needed to achieve precise manual movements. Whether you’re setting up or adjusting the machine for specific tasks, gaining proficiency in these controls will allow you to fully leverage the machine’s capabilities, ensuring both precision and reliability in your workflows.
Navigating the Machine Status Page
Accessing the Machine Status Page
Operators can access the machine status pages in a variety of ways.
Click on the icon STATE on the main programming page to enter the machine status page.
Alternatively, you can enter the machine status page by manually moving the page and clicking on the icon on the left.
Interpreting the System Signals
Click it to enter the machine status page.
On the machine status page, operators can observe the system’s input/output signals and analyze potential issues conveniently.
In the output window, click
, and the lower window will display the functional control status of each output port, as shown in the following figure:
If the box corresponding to the input/output command shows green, it indicates that the signal or function is normal.
Pole: Set the maximum height of the rise, which can be set only after the grating ruler is selected.
Implementing Manual Movement Controls
Initiating Manual Movement
To begin manual movement, click on the menu icon on the main programming page.
Select “Manual Move” from the pop-up menu, and enter the manual page. For security and accuracy, enter the password “0313” to set coordinates for the X/Y/R axis reference points.
Setting X-Axis Reference Points
Use a measuring tool to measure the reference position length from the clamping point to the back shield, then enter this value in the settings above the back shield icon.
This precision is key to ensuring correct HS-15T Manual Movement.
Configuring the Y-Axis Reference Points
Step on the foot and press it down to the bottom. Then use the measuring tool to measure the length of a reference position (from the bottom of the lower die to the top of the upper die).
Finally, write the measured value in the settings above the slider icon.
Adjusting the R-Axis Reference Points
The R-axis is critical for selecting the finger shield and must be coordinated with the X-axis to avoid die collision. Measure the distance between the lower die’s working plane and the stop finger, then input these values into the settings. Mastering this ensures optimal HS-15T Manual Movement.
Operating the Manual Speed Controls
On the manual movement screen, use the -/++ buttons for slow/fast movements. Click the “move” button next to the X/Y/R axis to move specified distances at set speeds. Click again to stop motion. Understanding speed controls is a key part of mastering HS-15T Manual Movement.
Set the Reference Point: Position the page at the reference point of your chosen axis. Hold it down to slowly move the motor in the direction of increasing count.
Decrease Count Direction: Similarly, set the page at the reference point, hold it down to slowly move the motor in the direction of subtraction.
Rapid Increase: For fast movements, set the page at the reference point, press and hold the designated button. The motor will rapidly move in the direction of increasing count.
Rapid Decrease: To quickly decrease, set the page at the reference point, press and hold the button to move the motor swiftly in the subtraction direction.
During these manual movements, the coordinates of the X/Y/R axis will dynamically change until the desired position is reached.
Attention: The HS-15T Manual Movement system is equipped with a position limit function. If the chosen position surpasses the set minimum or maximum limits, an alert “the given position exceeds the limit” will be displayed, and the action will be invalidated.
Häufig gestellte Fragen (FAQ)
How can I confirm that the HS-15T Manual Movement is functioning normally?
On the machine status page, green indicators in the input/output command boxes signify normal operation of the HS-15T Manual Movement controls.
What steps should I take to set the X-axis reference points?
Use a measuring tool to determine the length from the clamping point to the back shield. Enter this measurement into the settings above the back shield icon for precise HS-15T Manual Movement.
What happens if I attempt to exceed the position limits during HS-15T Manual Movement?
The system will display a “the given position exceeds the limit” message if the position exceeds the set minimum/maximum limits, preventing excessive movement.
Abschluss
Beherrschung der HS-15T Manual Movement Controls involves understanding key operational steps such as navigating the machine status page, setting reference points for the X, Y, and R axes, and effectively using manual speed controls. These actions ensure accurate and efficient control over manual movement, enhancing the machine’s performance and reliability in your production processes.
To further optimize your use of the HS-15T, consider consulting additional resources or contacting our support team for more detailed guidance. By staying informed and proactive, you can ensure your machinery operates at peak efficiency, reducing downtime and increasing productivity. For more information or personalized assistance, please reach out to our experts.
Aktualisiert am 11. Oktober 2025
