Accessing CybTouch 8 System Settings

To control CybTouch 8 System Settings efficiently, operators must first understand where these settings are located and how they affect machine operation. The System Settings page contains various configuration options that influence controller behavior, machine calibration, data management, and user experience.

Most of these settings apply globally to the controller rather than to individual bending programs. Therefore, changes should be made carefully and only after understanding their functions.

The System Settings page is commonly used during:

• Machine commissioning
• Controller setup
• Maintenance procedures
• Troubleshooting operations
• Production optimization

How to Control BDC Correction

BDC (Bottom Dead Center) Correction is one of the most important CybTouch 8 System Settings because it directly affects bending accuracy.

BDC Correction applies a permanent adjustment to the calculated Bottom Dead Center position.

Unlike temporary bend corrections, this value remains active for all programs until it is modified again.

BDC Correction is useful when:

• Consistent angle deviations occur
• The machine produces identical errors across different programs
• Minor calibration adjustments are required

However, excessive correction values may indicate underlying machine problems that should be investigated.

Best Practice

Before adjusting BDC Correction:

1. Verify tooling dimensions.
2. Check material settings.
3. Confirm machine calibration.
4. Review indexing accuracy.

Only apply BDC Correction after other potential causes have been eliminated.

How to Control RFLink Communication

RFLink is a service-related communication function available within CybTouch 8 System Settings.

Purpose of RFLink

RFLink allows the controller to communicate with a laptop equipped with a Cybelec RFLink dongle.

This function is primarily used for:

• Technical support
• Machine diagnostics
• Software maintenance
• Commissioning procedures

For security reasons, RFLink automatically returns to the OFF state after a controller restart.

Most operators will never need to activate this function during normal production.

How to Control Machine Indexation

Proper indexing is essential for accurate machine positioning.

Using Clear Indexation

The Clear Indexation function removes the current indexing data and starts a new indexing procedure without requiring a complete controller restart.

This feature can be useful when:

• Axis positions become inconsistent
• Maintenance work has been completed
• Position references need to be refreshed

Performing a new indexing cycle can help:

• Restore positioning accuracy
• Resolve synchronization issues
• Improve machine stability

How to Control USB File Management

USB Explorer provides a convenient method for transferring files between the controller and external USB storage devices.

Using USB Explorer

The USB Explorer function allows operators to:

• Browse USB folders
• Import part programs
• Export backup files
• Transfer tooling data

Recommended File Management Practices

To avoid compatibility issues:

• Use properly formatted USB devices.
• Keep exported files inside their original folders.
• Create regular backups of important programs.
• Verify file integrity after transfers.

Good file management practices help prevent accidental data loss.

How to Control Default Retraction Settings

Retraction settings determine how the backgauge moves during certain bending operations.

Default Retraction defines the standard retraction distance applied during programming.

The controller can automatically calculate retraction values in graphical programming mode, but operators may manually adjust them when necessary.

Correct retraction values help:

• Prevent workpiece collisions
• Improve part handling
• Increase production efficiency
• Reduce operator intervention

How to Control Date and Time Settings

Accurate date and time information is important for machine records and production traceability.

The Set Clock function allows users to adjust:

• Horas
• Minutos
• Seconds
• Day
• Month
• Year

Why Time Settings Matter

Correct clock settings improve:

• Maintenance tracking
• Production records
• Error logging
• Operational reporting

For machines connected to production management systems, accurate timestamps are especially important.

How to Control Touchscreen Performance

The touchscreen is the primary interface used for operating the CybTouch controller.

Performing Touchscreen Calibration

If touch accuracy decreases, calibration can restore proper operation.

To perform calibration:

1. Open the Touchscreen Calibration page.
2. Follow the on-screen instructions.
3. Touch the displayed targets accurately.
4. Save the calibration results.

Touchscreen Care Recommendations

Always use:

• Clean fingers
• Plastic styluses designed for touchscreens

Never use:

• Metal tools
• Destornilladores
• Sharp objects
• Excessive force

Proper touchscreen care helps maintain long-term reliability.

How to Control Display Settings

Several CybTouch 8 System Settings influence screen visibility and operator comfort.

Adjusting Brightness

Brightness settings allow operators to optimize screen visibility according to ambient lighting conditions.

Proper brightness levels improve:

• Readability
• Operator comfort
• Interface visibility

Using Eco Mode

Eco Mode automatically reduces display brightness to lower power consumption.

Benefits include:

• Reduced energy usage
• Extended screen lifespan
• Lower operating costs

Many operators enable Eco Mode during long production shifts.

How to Control Production Tracking

The Program Counter Mode helps monitor production quantities.

Counting Up Mode

The counter increases after each completed part.

Counting Down Mode

The counter decreases from a predefined target quantity until reaching zero.

Production Advantages

Using Program Counter Mode helps:

• Track production goals
• Monitor completed quantities
• Improve workflow planning
• Reduce counting errors

The counter value is automatically saved, even after power shutdown.

How to Control Advanced System Options

Several advanced settings provide additional flexibility for experienced users.

Mostrar L primero

This option determines how flange dimensions are displayed and entered.

Operators can choose between:

• External dimensions
• Actual backgauge positions

Disable Recalculation at Product Load

This setting controls whether the controller recalculates axis positions when loading existing programs.

Disabling recalculation may be useful when preserving previously validated production data.

Ayudas de indexación

Indexation Aids provide warning messages and guidance when indexing problems occur.

This feature helps operators identify and resolve positioning issues more efficiently.

Beam Stops During Retraction

This setting controls whether the beam pauses while the backgauge retracts.

Proper configuration can improve:

• Machine safety
• Cycle efficiency
• Workpiece handling

Best Practices for Controlling CybTouch 8 System Settings

To control CybTouch 8 System Settings effectively, operators should make adjustments only after understanding the purpose of each parameter. Routine settings such as brightness, clock configuration, and USB management can typically be modified by machine operators, while calibration and indexing-related parameters should be handled more carefully.

Documenting important changes and maintaining regular backups can further improve machine reliability. By learning how to control CybTouch 8 System Settings properly, operators can enhance machine performance, simplify maintenance tasks, and create a more efficient production environment.

Preguntas frecuentes (FAQ)

Understanding how to control CybTouch 8 System Settings is essential for maintaining reliable machine performance and optimizing daily operation. Features such as BDC Correction, touchscreen calibration, USB management, indexing functions, brightness adjustment, and production counters provide valuable tools that help operators customize the controller according to their production needs.

While many settings are designed to improve usability and efficiency, some parameters directly influence machine positioning and operational behavior. Therefore, changes should be made carefully, especially when modifying calibration or indexing-related functions.

By properly managing CybTouch 8 System Settings, operators can improve machine stability, simplify maintenance procedures, enhance productivity, and create a more efficient working environment. For additional support with CybTouch 8 configuration, troubleshooting, or advanced controller functions, feel free to contact the HARSLE technical support team or explore more HARSLE documentation resources.